Position Objective

• Technical engineering support for Custom Engineering system automation and electrical concept.
• Provision of systems engineering competence within the automation & electrical aspect.
• Advise customers on automation potential in manufacturing and assembly systems.
• Safeguarding and continuous improvement of the automation know-how.
• Support engineering team during Pre-FAT, FAT and SAT for instrumentation, electrical & automation related activities including documentation.

Essential Job Functions:

• Join the project bidding as Automation lead, including URS responds and automation & electronical proposal, cost analysis and demo show when required. (10%)
• Actively execute automation control system design, design review, test and start-up to meet the requirement of quality, safety, regulations complied and high-efficiency running. (35%)
• Manage the external partners on electrical design, including schematic drawing design, components selection, Technical inspect and approval the electrical construction, including wiring, installation of cable ducts, ensure the design & construction quality and timeline. (10%)
• Write, review automation and electrical related documents such as electrical schematic, HDS, SDS etc. to ensure compliance with URS and applicable regulations. (10%)
• Support during PreFAT, FAT and SAT activities in related but not limit to automation control, software, electrical aspects. (10%)
• Execute standardization of automation control software, electrical design and continuous improvement of software, electrical design and design standards. (10%)
• Technical support of different engineering disciplines throughout project duration and have right competence in external vendors, minor projects management and validation process. (10%)
• Support service activities, provide automation/electrical technical proposal and site execution including troubleshooting, retrofit, software upgrade etc. Share typical troubleshooting cases with service team. (5%)

Minimum Qualifications:

• Skilled in Design and configure DeltaV DCS systems (Control Modules, Equipment Modules, Batch); Develop control logic; Build HMI/graphics and alarm systems.
• Skilled in PLC&SCADA design, such as Siemens TIA portal & Simatic Wincc.
• Design experience on VFD and servo controller.
• Familiar with industrial process instruments and field buses.
• Skilled of electrical components selection and electrical drawing design by AutoCAD or EPLAN.
• Cost estimation of automation and electrical concept, cost evaluation based on the concept designed.
• Troubleshooting automation & electrical problems.
• Coordinate with PM/PE, engineering support team & sub-suppliers/partners to implement lean production.
• Coordination of systems partners for the realization of automation systems and support for the global Custom Engineering strategy.
• Commitment to work together with engineering support team and willingness to work with an interdisciplinary team including sub-suppliers/partners, customers’ representatives and international colleagues to meet customers’ expectations.
• Ability to communicate effectively into team, identifying duties and responsibilities and proposing best suitable solutions.
• Open minded and flexible in looking for new technologies and continuous improvement.

Essential Qualifications & Education:

• Bachelor’s degree or above in automation or electrical engineering

Essential Experience:

• Expert in Emerson DeltaV software/hardware configuration, programming, and commissioning.
• Experience with mainstream PLC and SCADA systems, such as Siemens PLC and Simatic Wincc.
• Knowledge about GAMP 5, ISA88, 21CFR PART11 and GMP.
• Experience in preferably pharma/biotech industry or alternatively in the food/beverage/cosmetics industry.
• With strong team work consciousness and good cooperation, open mind and strong implementation.
• Good communication and coordination skills.
• Able to work with dynamic changes and pressure.
• Good English speaking, reading and writing skills.

Position Competencies

• Detailed knowledge and understanding of design criteria for automation & electrical in biopharmaceutical systems.
• Support teamwork within the interdisciplinary group and in relation to project managers and process/project engineers.
• Travelling to customer & supplier sites is needed.

Other Requirements

• To work safely and to comply with the company’s health, safety and environmental (HSE) policies and procedures
• To keep your work area tidy and free from hazards.
•  Report and address any safety defects.

Join our winning team today. Together, we’ll accelerate the real-life impact of tomorrow’s science and technology. We partner with customers across the globe to help them solve their most complex challenges, architecting solutions that bring the power of science to life.

For more information, visit www.danaher.com.